Data Migration - Errors

If a Migration Error occurs as shown below, here is the solution.


Error code(Prefix) Error code(Postfix) Error description Cause Solution Note
201109 031195 Export Disk has failed. Information for the source disk could not be retrieved [1] Windows Snapshot Service has been stopped or is not installed. [1-1] Install shadow copy client, and run Data Migration
- ShadowCopyClient.msi Install

[1-2] At Disk Management -> Services, change the startup types for Microsoft Software Shadow Copy Provider and Volume Shadow Copy to Automatic, and then run Data Migration When the error code 201109(031195) occurs,
refer to Troubleshooting
Errors.docx
(FAQ 1.)
205500 0322BC An error has occurred while reading the source disk. [1] There is a problem (logical or mechanical) with the source disk
[2] SSD is not properly connected
[3] Port detection problem [1-1] Run Chkdsk with administrator privileges.
If there is a problem with the disk, use the Chkdsk /f /r command to reboot the system and recover the disk error before re-attempting Migration.
However, if the Windows File System is damaged, migration is impossible

[1-2] If there is a problem with the source disk, migration is impossible

[2] If connected to SATA to SATA, change the target disk to SATA to USB
(If connected to SATA to USB, change the target disk to SATA to SATA)

[3] The problem may lie with the port, so try again using a different port When the error code 205500, 301400,
400180, or 400200 occurs,
refer to Troubleshooting
Errors.docx
(FAQ 2.)
301400 497C8 ~ 4B708 An error has occurred while defragmenting the target disk. [1] There is a problem (logical or mechanical) with the source disk
[2] SSD is not properly connected
[3] Port detection problem [1-1] Run Chkdsk with administrator privileges.
If there is a problem with the disk, run the Chkdsk /f /r command to reboot the system and recover the disk error before re-attempting Migration.
However, if Windows File System is damaged, migration is impossible

[1-2] If there is a problem with the source disk, migration is impossible

[2] If connected as SATA to SATA, change the target disk to SATA to USB
(If connected as SATA to USB, change the target disk to SATA to SATA)

[3] The problem may lie with the port, so try again using a different port When the error code 205500, 301400,
400180, or 400200 occurs,
refer to Troubleshooting
Errors.docx
(FAQ 2.)
400180 061B34 Export Disk has failed.
An error has occurred while writing to the target disk. [1] There is a problem (logical or mechanical) with the source disk
[2] SSD is not properly connected
[3] Port detection problem [1-1] Run Chkdsk with administrator privileges.
If there is a problem with the disk, run the Chkdsk /f /r command to reboot the system and recover the disk error before re-attempting Migration.
However, if the Windows File System is damaged, migration is impossible

[1-2] If there is a problem with the source disk, migration is impossible

[2] If connected as SATA to SATA, change the target disk to SATA to USB
(If connected as SATA to USB, change the target disk to SATA to SATA)

[3] The problem may lie with the port, so try again using a different port When the error code 205500, 301400,
400180, or 400200 occurs,
refer to Troubleshooting
Errors.docx
(FAQ 2.)
400200 061B48 Export Disk has failed.
An error has occurred while writing to the target disk. [1] There is a problem (logical or mechanical) with the source disk [1] If the problem is caused by a problem with the source disk, Data Migration is impossible. When the error code 205500, 301400,
400180, or 400200 occurs,
refer to Troubleshooting
Errors.docx
(FAQ 2.)
Access
Violation Access Violation at address 7071cc63 in module 'restore.dll' read of address 00000000 [1] A conflict occurred with the Data Migration Program during migration [1] Contact Clonix Customer Support